Flashforge Creator Pro: Difference between revisions
No edit summary |
No edit summary |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 12: | Line 12: | ||
== Advisories == | == Advisories == | ||
{{Warning|1='''Do not take this printer over 250c. Avoid 250c temperatures for long periods.'''}} Try to keep it at a maximum of 245c. This printer does not have an all-metal hot end, it is a PTFE (Teflon) lined hot end. '''PTFE will start to degrade over 250c, and will emit toxic fumes above 275c.''' This printer does not have a known good-quality PTFE tube installed, so it could emit toxic fumes below this. One source recommends this specific printer not be set to go above 240c. | |||
Please keep the SD card in the machine when you're done with it. | Please keep the SD card in the machine when you're done with it. | ||
| Line 19: | Line 21: | ||
The filament spool is around the back. Currently, only the left extruder is hooked up. There is no spool holder for the right extruder, nor is there a bowden tube. For easier access, you can go into the server room and open the door that is behind the shelf. | The filament spool is around the back. Currently, only the left extruder is hooked up. There is no spool holder for the right extruder, nor is there a bowden tube. For easier access, you can go into the server room and open the door that is behind the shelf. | ||
Please do not use gluesticks unless you absolutely need to. | Please do not use gluesticks unless you absolutely need to. When using glue, use the side of the plate that has already had glue applied. Glue should not be necessary for PETG or PLA. | ||
== History == | |||
{| class="wikitable" | |||
! Info !! Date | |||
|- | |||
| Donated by Zach || ? | |||
|- | |||
| Bed leveled by Tara || 11/18/24 | |||
|} | |||
[[Category:Hardware]] | [[Category:Hardware]] | ||
Latest revision as of 07:22, 19 November 2024
3D printer, the one that's black, boxxy, and partially enclosed. This machine is located in the Focus Foundry.
How to Slice
The recommended slicer is FlashForge's proprietary slicer, FlashPrint. FlashPrint does not work on modern MacOS and is generally just old as shit.
You do not need to use FlashPrint, however, this printer only accepts .x3g files. To convert from .gcode to x3g, postprocessing needs to be done. Check here for how to get PrusaSlicer setup to print on this machine. The included config bundles are known good and produce pretty good parts from limited testing.
FlashPrint will be more plug and play though. So if you can get it installed and working, it might be the faster option.
This printer prints from an SD card. The slot is behind the front lip.
Advisories
 Warning: | Do not take this printer over 250c. Avoid 250c temperatures for long periods. |
Try to keep it at a maximum of 245c. This printer does not have an all-metal hot end, it is a PTFE (Teflon) lined hot end. PTFE will start to degrade over 250c, and will emit toxic fumes above 275c. This printer does not have a known good-quality PTFE tube installed, so it could emit toxic fumes below this. One source recommends this specific printer not be set to go above 240c.
Please keep the SD card in the machine when you're done with it.
Please turn off the machine when you are done with it. The power button is on the left side, rear panel, past the power cable.
The filament spool is around the back. Currently, only the left extruder is hooked up. There is no spool holder for the right extruder, nor is there a bowden tube. For easier access, you can go into the server room and open the door that is behind the shelf.
Please do not use gluesticks unless you absolutely need to. When using glue, use the side of the plate that has already had glue applied. Glue should not be necessary for PETG or PLA.
History
| Info | Date |
|---|---|
| Donated by Zach | ? |
| Bed leveled by Tara | 11/18/24 |